====== Router Basic Configuration ======


==== BASIC DEVICE COMMANDS ====

Show Running Configuration File
  >show running-config
Show Startup Configuration File (NVRAM)
  >show startup-config
Show Flash Memory Information
  >show flash
Show Command History
  >show history
Copy Changes from Running Config to the Startup Config
  #copy running-config startup-config
Show Version (Platform Type / OS Revision / Last Boot / Memory / Interfaces /Conf Register)
  >show version
Show Devices Clock (Time/Date)
  >show clock
Show Users Connected to Device
  >show users

====DEVICE SECURITY====

Set password exec & non-exec (console / aux / telnet)
  >enable
  #configure terminal
  #enable password EnablePass1
  #line console 0
  #login
  #password ConsolePass1
  #exit
  
  #line aux 0
  #login
  #password AuxPass1
  #exit
  
  #line vty 0 4
  #login
  #password TelnetPass1
  #exit
Set Secret Password (recommended method)
  >enable
  #configure terminal
  #enable secret EnableSecret1
  #exit

====BASIC SETINGS====

Set a Warning Banner For Login Prompt
  >enable
  #configure terminal
  #banner motd &
  #banner line1
  #banner line2 &
  #exit
Set hostname
  >enable
  #configure terminal
  #hostname router1
  #prompt router01
  #exit

====SAVING AND RESTORING CONFIGURATIONS====

​Save Running Config to Startup Config
  ​#copy running-configuration startup-configuration
​Save Running Config to a Remote TFTP Server
  ​#copy running-configuration tftp
  ​<enter IP>
  ​<enter filename>
​Save Config From Remote TFTP Server to the Running Config
  ​#copy tftp running-configuration
  ​<enter IP>
  ​<enter filename>
​Erase NVRAM
  ​#erase nvram

====INTERFACE COMAMNDS====

Show Summary of All Interfaces (IP & Status)
  >show ip interface brief
Show Detailed Interface Information (All Interfaces)
  >show interfaces
Show Detailed Interface Information (Single Interface)
  >show interfaces serial 0
Show Detailed Interface Protocol Information (Single Interface)
  >show ip interface serial 0
Show Status of Interface Layer 3 Protocols
  >show protocols
Show Information About IP Routing Protocols
  >show ip protocols
Show IP Routes (Interfaces that are routing)
  >show ip route
Show Cached Hosts List
  >show hosts
Set description for an interface
  >enable
  #configure terminal
  #interface serial 0
  #description this is the serial0 link to router2
  #exit
Configure an IP for an interface
  #configure terminal
  #interface Ethernet 0
  #ip address 10.1.1.251 255.255.255.0
  #exit
Enable an Interface
  #configure terminal
  #interface Ethernet 0
  #no shutdown
  #exit
Disable an Interface (Administratively Down)
  #configure terminal
  #interface Serial 1
  #shutdown
  #exit

====SERIAL INTERFACES====

Set Serial Interface Clock Rate (DCE Cable – Data Circuit-Terminating Equipment)
  R1#configure terminal
  R1#interface serial 0
  R1#clock rate 56000
  R1#no shut
  R2#configure terminal
  R2#interface serial 0
  R2#no shut
Set Serial Interface Bandwidth and Clock Rate
  #configure terminal
  #interface serial 0
  #bandwidth 64
  #clock rate 64000
  #exit

====LOOPBACK INTERFACES====

Create a Loopback Interface and Set the IP Address and Mask
  R1#configure terminal
  R1#interface loopback 0
  R1#ip address 10.1.100.1 255.255.255.0
  R1#no shut

====CDP (Cisco Discovery Protocol)====

Show CDP General Information
  >show cdp
Show CDP Interface Information
  >show cdp interface
Show CDP Neighbors
  >show cdp neighbors
Show CDP Neighbors Detail
  >show cdp neighbors detail
Show Specific CDP Entry Details
  >show cdp entry R4
Set / Adjust the Time between CDP Updates
  #configure terminal
  (config)#cdp timer 45
Set / Adjust the CDP Information Hold Time
  #configure terminal
  (config)#cdp holdtime 60
Disable CDP on the Entire Router
  #configure terminal
  (config)#no cdp run
Enable CDP on the Entire Router
  #configure terminal
  (config)#cdp run
Disable CDP on an Interface
  #configure terminal
  (config)#interface Ethernet 0
  (config-if)#no cdp run  
Enable CDP on an Interface
  #configure terminal
  (config)#interface Ethernet 0
  (config-if)#cdp run

====ARP====

Show ARP Table
  >show arp
Clear ARP Table
  #clear arp

====TELNET====

Telnet to another Device
  >telnet 10.1.1.2
  password: ****
Show Sessions
  >show sessions
Disconnect from a session
  >disconnect 1
Setup to Allow Telnet Logins
  #conf term
  (config)#line vty 0 4
  (config-line)#login
  (config-line)#password Pass1

====HOSTS TABLE====

​Add an Entry to the Hosts Table
  #conf term
  (config)#ip host California 192.168.10.1

====STATIC ROUTING====

​Show IP Routes (S = Static)
  ​>show ip route
​Add a Static Route
  ​#conf term
  ​#ip route 10.1.1.0 255.255.255.0 192.168.10.1
Remove a Static Route
  ​#conf term
  ​#no ip route 10.1.1.0 255.255.255.0 192.168.10.1

====DEFAULT ROUTING====

​Show IP Routes (S = Static * = Default Candidate)
  ​>show ip route
​Add a Default Route
  ​#conf term
  #ip route 0.0.0.0 0.0.0.0 192.168.10.1
Remove a Default Route
  ​#conf term
  ​#no ip route 0.0.0.0 0.0.0.0 192.168.10.1

====RIP (Routing Information Protocol)====
Uses UDP port 520

Show IP Routes (R = RIP)
  ​>show ip route
Show Information About IP Routing Protocols
  >show ip protocols
​Enable RIP
  ​#conf term
  ​#router rip
​Disable RIP
  ​#conf term
  ​#no router rip

​Add a Network for RIP Advertisements/Receives (Delay <30secs)
​  #conf term
  ​#router rip
  ​#network 10.0.0.0
Remove a Network from RIP Advertisements/Receives
  ​#conf term
  #router rip
  ​#no network 10.0.0.0
​Turn on RIP Debugging
  ​#debug ip rip
Turn off RIP Debugging
  ​#no debug ip rip
Clear and Re-Create IP Routing Table
  ​#clear ip route *

====IGRP (Interior Gateway Routing Protocol)====

Show IP Routes (I = IGRP)
  ​>show ip route
Show Information About IP Routing Protocols
  >show ip protocols
​Enable IGRP
  ​#conf term
  ​#router igrp 100
​Add Networks Directly Connected to Router for IGRP Routing
  #conf term
  ​#router igrp 100
  ​#network 10.0.0.0
Remove Networks Directly Connected to Router for IGRP Routing
  #conf term
  ​#router igrp 100
  ​#no network 10.0.0.0

====EIGRP (Enhanced Interior Gateway Routing Protocol)====

Show IP Routes (D = EIGRP)
  ​>show ip route
Show Information About IP Routing Protocols
  >show ip protocols
Show EIGRP Neighbours
  >show ip eigrp neighbours
Show EIGRP Traffic, Shows EIGRP Packet Types Sent and Recieved
  >show ip eigrp traffic
​Enable EGRP 100
  ​#conf term
  ​#router eigrp 100
​Add Networks Directly Connected to Router for EIGRP Routing
  #conf term
  ​#router eigrp 100
  ​#network 10.0.0.0
Remove Networks Directly Connected to Router for EIGRP Routing
  #conf term
  ​#router eigrp 100
  ​#no network 10.0.0.0

====OSPF (Open Shortest Path First) Routing====
Show Routing Table (O = OSPF)
  >show ip route
Show Routing Protocol Information
  >show ip protocols
Show the OSPF Database
  >show ip ospf database
Show OSPF Neighbours
  >show ip ospf neighbour
Show Interfaces Running OSPF – Detailed Information
  >show ip ospf interface
Configure OSPF Routing and Set the Process Number
  R1#conf term
  R1(config)#router ospf 100
  
  R2#conf term
  R2(config)#router ospf 100
  
  R3#conf term
  R3(config)#router ospf 100
Configure Networks that the Router is Connected to
  R1#conf term
  R1(config)#router ospf 100
  R1(config-router)#network 10.1.20.0 0.0.0.255 area 0
  R1(config-router)#network 192.16.1.0 0.0.255.255 area 0
  
  R2#conf term
  R2(config)#router ospf 100
  R2(config-router)#network 10.1.20.0 0.0.0.255 area 0
  
  R3#conf term
  R3(config)#router ospf 100
  R3(config-router)#network 192.16.1.0 0.0.255.255 area 0

====PPP (Point-to-Point Protocol)====

===With CHAP Authentication (Challenge-Handshake Authentication Protocol)===
==R1==
Set the Enable Secret on R1
  R1#conf term
  R1#enable secret secretPassR1
Create a User on R1 with Same Password as R2’s Enable Secret
  R1#username R2 password secretPassR2
Set an IP and Enable the Serial Interface on R1
  R1#interface serial 0
  R1#ip address 10.1.0.1 255.255.255.0
  R1#no shutdown
Set Encapsulation for the Serial Interface to PPP on R1
  R1#encapsulation ppp
Set PPP Authentication to CHAP for the Serial Interface on R1
  R1#ppp authentication chap

==R2==
Set the Enable Secret on R2
  R2#conf term
  R2#enable secret secretPassR2
Create a User on R2 with Same Password as R1’s Enable Secret
  R1#username R1 password secretPassR1
Set an IP and Enable the Serial Interface on R2
  R2#interface serial 0
  R2#ip address 10.1.0.2 255.255.255.0
  R2#no shutdown
Set Encapsulation for the Serial Interface to PPP on R2
  R2#encapsulation ppp
Set PPP Authentication to CHAP for the Serial Interface on R2
  R2#ppp authentication chap
Show Serial Interface Details including Encapsulation Type
  >show interfaces serial 0

===Without CHAP Authentication===

==R1==
Set an IP and Enable the Serial Interface on R1
  R1#conf term
  R1#interface serial 0
  R1#ip address 10.1.0.1 255.255.255.0
  R1#no shutdown
Set Encapsulation for the Serial Interface to PPP on R1
  R1#encapsulation ppp

==R2==
Set an IP and Enable the Serial Interface on R2
  R2#conf term
  R2#interface serial 0
  R2#ip address 10.1.0.2 255.255.255.0
  R2#no shutdown
Set Encapsulation for the Serial Interface to PPP on R2
  R2#encapsulation ppp
Show Serial Interface Details including Encapsulation Type
  >show interfaces serial 0

====ISDN (Integrated Services Digital Network)====

​Show ISDN Status (Check Layer1 = Active, Layer2 = Multi-Frame Established)
  ​>show isdn status
​Show ISDN Interface Information
  ​>show interface bri 0
Specify the ISDN Switch Type
  #conf term
  ​#isdn switch-type basic-ni
​Set the SPID for the Interface
  ​#interface bri 0
  ​#isdn spid1 32177820010100
​Set the Dialler String on the Interface to Establish Layer 3
  ​#interface bri 0
  ​#dialer string 7782002
​Setup a Dialer-list to Permit All IP Traffic
  ​#dialer-list 1 protocol ip permit

===ISDN BRI-BRI using Legacy DDR (Dial on Demand Routing)===

​Show ISDN Status (Check Layer1 = Active, Layer2 = Multi-Frame Established)
  ​>show isdn status
​Configure ISDN BRI-BRI using Legacy DDR
  ​R1(config)#isdn switch-type basic-ni
  R1(config)#dialer-list 1 protocol ip permit
  R1(config)#username R2 password cisco
  R1(config)#interface bri0
  R1(config-if)#encapsulation ppp
  R1(config-if)#ip address 200.10.1.1 255.255.255.0
  R1(config-if)#isdn spid1 32177820010100
  R1(config-if)#dialer-group 1
  R1(config-if)#dialer map ip 200.10.1.2 name R2 broadcast 7782001
  R1(config-if)#ppp authentication chap
  R1(config-if)#no shut
  
  R2(config)#isdn switch-type basic-ni
  R2(config)#dialer-list 1 protocol ip permit
  R2(config)#username R1 password cisco
  R2(config)#interface bri0
  R2(config-if)#encapsulation ppp
  R2(config-if)#ip address 200.10.1.1 255.255.255.0
  R2(config-if)#isdn spid1 32177820020100
  R2(config-if)#dialer-group 1
  R2(config-if)#dialer map ip 200.10.1.1 name R1 broadcast 7782002
  R2(config-if)#ppp authentication chap
  R2(config-if)#no shut

===ISDN BRI-BRI using Dialer Profiles===

​Show ISDN Status (Check Layer1 = Active, Layer2 = Multi-Frame Established)
  ​>show isdn status
​Configure ISDN BRI-BRI using Dialer Profiles
  ​R1(config)#isdn switch-type basic-ni
  R1(config)#dialer-list 1 protocol ip permit
  R1(config)#username R2 password cisco
  R1(config)#int bri0
  R1(config-if)#encap ppp
  R1(config-if)#ppp authentication chap
  R1(config-if)#isdn spid1 32177820010100
  R1(config-if)#dialer pool-member 1
  R1(config-if)#no shut
  R1(config-if)#int dialer 1
  R1(config-if)#no shut
  R1(config-if)#ip address 200.10.1.1 255.255.255.0
  R1(config-if)#encap ppp
  R1(config-if)#dialer-group 1
  R1(config-if)#dialer pool 1
  R1(config-if)#dialer remote-name R2
  R1(config-if)#dilaer string 7782001
  R1(config-if)#ppp authentication chap
   
  R2(config)#isdn switch-type basic-ni
  R2(config)#dialer-list 1 protocol ip permit
  R2(config)#username R1 password cisco
  R2(config)#int bri0
  R2(config-if)#encap ppp
  R2(config-if)#ppp authentication chap
  R2(config-if)#isdn spid1 32177820020100
  R2(config-if)#dialer pool-member 1
  R2(config-if)#no shut
  R2(config-if)#int dialer 1
  R2(config-if)#no shut
  R2(config-if)#ip address 200.10.1.2 255.255.255.0
  R2(config-if)#encap ppp
  R2(config-if)#dialer-group 1
  R2(config-if)#dialer pool 1
  R2(config-if)#dialer remote-name R1
  R2(config-if)#dilaer string 7782002
  R2(config-if)#ppp authentication chap

===ISDN PRI using Dialer Profiles===

​Show ISDN Status (Check Layer1 = Active, Layer2 = Multi-Frame Established)
  ​>show isdn status
​Configure ISDN PRI using Dialer Profiles
  ​R1(config)#isdn switch-type basic-ni
  R1(config)#dialer-list 1 protocol ip permit
  R1(config)#username R2 password cisco
  R1(config)#interface bri0
  R1(config-if)#encap ppp
  R1(config-if)#ppp authentication chap
  R1(config-if)#isdn spid1 32177820010100
  R1(config-if)#dialer pool-member 1
  R1(config-if)#no shut
  R1(config-if)#int dialer 2
  R1(config-if)#no shut
  R1(config-if)#ip add 201.10.1.1 255.255.255.0
  R1(config-if)#encap ppp
  R1(config-if)#dialer-group 1
  R1(config-if)#dialer pool 1
  R1(config-if)#dialer remote-name R2
  R1(config-if)#dialer string 7782001
  R1(config-if)#ppp authentication chap
  
  R2(config)#isdn switch-type primary-5ess
  R2(config)#dialer-list 1 protocol ip permit
  R2(config)#username R1 password cisco
  R2(config)#controller tl 0/0
  R2(config-contoller)#framing esf
  R2(config-contoller)#linecode b8zs
  R2(config-contoller)#pri-group timeslots 1-24
  R2(config-contoller)#exit
  R2(config)#interface serial0/0:23
  R2(config-if)#encapsulation ppp
  R2(config-if)#ppp authentication chap
  R2(config-if)#dialer pool-member 2
  R2(config-if)#no shut
  R2(config-if)#interface dialer 2
  R2(config-if)#ip add 201.10.1.2 255.255.255.0
  R2(config-if)#encaps ppp
  R2(config-if)#dialer-group 1
  R2(config-if)#dialer pool 2
  R2(config-if)#dialer remote-name R1
  R2(config-if)#dialer string 7782002
  R2(config-if)#ppp authentication chap
  R2(config-if)#no shut

====IPX (Internetwork Packet Exchange)====

​Show IPX Interface Information
  ​>show ipx interface
Show IPX Interface Information Brief
  ​>show ipx interface brief
​Show IPX Traffic
  ​>show ipx traffic
Enable IPX Routing on Both Routers
  #conf term
  #ipx routing
Assign an IPX Network to the Ethernet Interfaces on the Routers
  #interface Ethernet 0
  (config-if)#ipx network AAA
  (config-if)#no shut

====FRAME RELAY====

Show Global Frame-Relay Traffic Statistics
  >show frame-relay traffic
Show Frame-Relay LMI (Local Management Interface) Traffic
  >show frame-relay lmi
Show Frame-Relay Mappings of DLCI (Layer 2) to the IP Address (Layer 3)
  >show frame-relay map
Show Frame-Relay PVC (Permanent Virtual Circuit) Mappings between Router and the Frame-Relay Switch
  >show frame-relay pvc
Set the Interfaces Encapsulation to Frame-Relay on Both Routers
  #interface serial 0
  #encapsulation frame-relay
  #no shut
Set the Frame-Relay Interface DLCI (Data Link Connection Identifer) for the Connection
  R1(config-if)#frame-relay interface-dlci 102
  
  R2(config-if)#frame-relay interface-dlci 202
Create Sub Interface and IP for Each Connection and Set DLCI on Connections
  R1(config-if)#interface serial 0.100 point-to-point
  R1(config-subif)#frame-relay interface-dlci 102
  R1(config-subif)#ip address 172.16.1.1 255.255.255.0
  R1(config-if)#interface serial 0.200 point-to-point
  R1(config-subif)#frame-relay interface-dlci 103
  R1(config-subif)#ip address 172.16.1.2 255.255.255.0
   
  R2(config-if)#interface serial 0.100 point-to-point
  R2(config-subif)#frame-relay interface-dlci 201
  R2(config-subif)#ip address 172.16.2.1 255.255.255.0
   
  R3(config-if)#interface serial 0.100 point-to-point
  R3(config-subif)#frame-relay interface-dlci 301
  R3(config-subif)#ip address 172.16.2.1 255.255.255.0
Set the LMI (Local Management Interface) Type
  #conf term
  (config)#int serial1
  (config-if)#frame-relay lmi-type ansi
Set Frame Relay Map IP
  #conf term
  (config)#int serial1
  (config-if)#frame-relay map ip 10.50.1.1 105 broadcast

====STANDARD ACCESS LISTS====

Show Access Lists
  >show access-lists
  >show access-lists 1
  >show access-lists 99
View Access Lists Applied to an Interface
  >show ip interface
  access-list [#(1-99) ] [permit | deny] [source-address | keyword any] [source mask]
Create an Access List to Deny
  #conf term
  (config)#access-list 1 deny host 192.168.20.1
  (config)#access-list 1 deny 192.168.20.2
  (config)#access-list 1 deny 192.168.20.3 0.0.0.0
Create an Access List to Permit
  #conf term
  (config)#access-list 1 permit any
Delete an Access List
  #conf term
  (config)#no access-list 1
  ip access-group [access-list] [in | out]
Add the Access Group to an Interface (in/out)
  #conf term
  (config)#interface ethernet 0
  (config-if)#ip access-group 1 in
  (config-if)#ip access-group 20 out
Remove the Access Group from an Interface (in/out)
  #conf term
  (config)#interface ethernet 0
  (config-if)#no ip access-group 1 in

====EXTENDED ACCESS LISTS====

Show Access Lists
  >show access-lists
  >show access-lists 101 (100-199 and 2000-2699)
View Access Lists Applied to an Interface
  >show ip interface
Create an Extended Access List
  #conf term
  (config)#access-list 101 deny icmp any any echo
  (config)#access-list 101 permit tcp 24.17.2.16 0.0.0.15 any eq telnet log
  (config)#access-list 102 permit tcp 24.17.2.0 0.0.0.15 any log
  (config)#access-list 103 permit ip host 192.168.1.123 host 192.168.1.12 log
Delete an Extended Access List
  #conf term
  (config)#no access-list 101 permit tcp 24.17.2.16 0.0.0.15 any eq telnet log
Add the Access Group to an Interface (in/out)
  ip access-group [access-list] [in | out]
  #conf term
  (config)#interface ethernet 0
  (config-if)#ip access-group 101 in
  (config-if)#ip access-group 102 out
Remove the Access Group from an Interface (in/out)
  #conf term
  (config)#interface ethernet 0
  (config-if)#no ip access-group 101 in

====NAMED ACCESS CONTROL LISTS====

Show Access Lists
  >show access-lists
Create a Named Access List to Deny Ping and Log
  #conf term
  (config)#ip access-list extended deny_icmp_ping
  (config-ext-acl)#deny icmp host 192.168.1.20 192.168.1.1 0.0.0.0 log
  (config-ext-acl)#permit ip any any log
Delete a Named Access List
  #conf term
  (config)#no ip access-list extended deny_icmp_ping
Add the Named Access Group to an Interface (in/out)
  #conf term
  (config)#interface FA0/0
  (config-if)#ip access-group deny_icmp_ping in
Remove the Named Access Group from an Interface (in/out)
  #conf term
  (config)#interface FA0/0
  (config-if)#no ip access-group deny_icmp_ping in

====NAT/PAT (Network Address Translation/Port Address Translation)====

Show IP NAT Translations
  >show ip nat translations
Clear IP NAT Translations
  #clear ip nat translation *
Show IP NAT Statistics
  >show ip nat statistics

===STATIC NAT===

Add a Static NAT
  #conf term
  (config)#ip nat inside source static 10.50.1.2 10.70.1.2
  (config)#interface ethernet 0
  (config-if)#ip nat inside
  (config-if)#interface serial 0
  (config-if)#ip nat outside
Remove a Static NAT
  #conf term
  (config)#no ip nat inside source static 10.50.1.2 10.70.1.2

===MANY-TO-ONE NAT===

Add a Many-To-One NAT
  #conf term
  (config)#access-list 11 permit 10.50.1.0 0.0.0.255
  (config)#ip nat inside source list 11 interface serial 0 overload
  (config)#interface ethernet 0
  (config-if)#ip nat inside
  (config-if)#interface serial 0
  (config-if)#ip nat outside
Remove a Many-To-One NAT
  #conf term
  (config)#no ip nat inside source static 10.50.1.2 10.70.1.2

===DYNAMIC NAT (Using Pools)===

Add a Dynamic NAT
  #conf term
  (config)#ip nat pool poolname1 10.50.1.100 10.50.1.150 netmask 255.255.255.0
  (config)#ip nat inside source list 2 pool poolname1
  (config)#interface ethernet 0
  (config-if)#ip nat inside
  (config-if)#interface serial 0
  (config-if)#ip nat outside
Remove a Dynamic NAT
  #conf term
  (config)#no ip nat pool pool1 10.50.1.100 10.50.1.150 netmask 255.255.255.0

===PAT (Port Address Translation)===

Add a PAT
  #conf term
  (config)#ip nat inside source list 2 interface serial 0 overload
Remove a PAT
  #conf term
  (config)#no ip nat inside source list 2 interface serial 0 overload