The Book

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
=== Reset 3COM Switch to Factory Defaults ===

The default password for a 3COM 2928 SFP:

  Username: admin
  Password: <blank>

To perform the factory default reset of the switch I did the following:

1. Connect a Cisco (light blue) console cable between a computer (serial) and the 3COM switch (RJ45 console port)

2. Open PUTTY with a serial connection and the following settings (38400, 8, 1, N)

3. Power on the 3COM switch and wait for the "Starting....." text to appear
<code>
Starting......

    ************************************************************************
    *                                                                      *
    *              3COM 2928-SFP Plus BOOTROM, Version 119                 *
    *                                                                      *
    ************************************************************************
    Creation Date       : Feb  3 2010
    CPU L1 Cache        : 32KB
    CPU Clock Speed     : 333MHz
    Memory Size         : 128MB
    Flash Size          : 128MB
    CPLD Version        : 002
    PCB Version         : Ver.B
    Mac Address         : 002473959EC8 
</code>
 
4. When "Press Ctrl-B to enter Extended Boot menu..." appears, press "CTRL+B"
<code>
Press Ctrl-B to enter Extended Boot menu...0
Please input BootRom password:

   BOOT MENU
</code>
 
5.  Press "7" to "Skip current system configuration"
<code>
1. Download application file to flash
2. Select application file to boot
3. Display all files in flash
4. Delete file from flash
5. Modify BootRom password
6. Enter BootRom upgrade menu
7. Skip current system configuration
8. Set BootRom password recovery
9. Set switch startup mode
0. Reboot

Enter your choice(0-9): 7
</code>

7. Press "Y" to skip the current config at next reboot
<code>
The current setting will run with current configuration file when reboot.
Are you sure you want to skip current configuration file when reboot? Yes or
No (Y/N):Y
Setting...Done!
</code>

8. Now Press "0" to reboot the switch
<code>
   BOOT MENU

1. Download application file to flash
2. Select application file to boot
3. Display all files in flash
4. Delete file from flash
5. Modify BootRom password
6. Enter BootRom upgrade menu
7. Skip current system configuration
8. Set BootRom password recovery
9. Set switch startup mode
0. Reboot

Enter your choice(0-9): 0
</code>

9. The switch will reboot, allow it to fully boot this time
<code>
Starting......

    ************************************************************************
    *                                                                      *
    *              3COM 2928-SFP Plus BOOTROM, Version 119                 *
    *                                                                      *
    ************************************************************************
    Creation Date       : Feb  3 2010
    CPU L1 Cache        : 32KB
    CPU Clock Speed     : 333MHz
    Memory Size         : 128MB
    Flash Size          : 128MB
    CPLD Version        : 002
    PCB Version         : Ver.B
    Mac Address         : 002473959EC8


Press Ctrl-B to enter Extended Boot menu...0
Starting to get the main application file--flash:/S2900-CMW520-R1101P09.bin!...
..........................................................................
The main application file is self-decompressing................................
...............................................................................
.........................Done!
System is starting...
Configuration file is skipped.
User interface aux0 is available.
</code>
 

 

10. Press "Enter", you will not need a password to login.
<code>
Press ENTER to get started.
<3Com Baseline Switch>
#Apr 26 12:00:16:292 2000 3Com Baseline Switch SHELL/4/LOGIN:
 Trap 1.3.6.1.4.1.43.45.1.10.2.2.1.1.3.0.1<h3cLogIn>: login from Console VMadmin.co.uk
%Apr 26 12:00:16:461 2000 3Com Baseline Switch SHELL/4/LOGIN: Console login from aux0
<3Com Baseline Switch>
</code>
 
11. Now type "initialize" to delete the configuration file and reboot the switch once more, Press "Y" to accept reboot.
<code>
<3Com Baseline Switch>initialize
 The startup configuration file will be deleted and the system will be rebooted. Continue? [Y/N]:Y
 Please wait...
#Apr 26 12:00:33:537 2000 3Com Baseline Switch DEV/1/REBOOT:
 Reboot device by command.

%Apr 26 12:00:33:641 2000 3Com Baseline Switch DEV/4/SYSTEM REBOOT:
 System is rebooting now.
</code>
 
12. The switch will full start up again, this time completely factory reset.
<code>
Starting......

    ************************************************************************
    *                                                                      *
    *              3COM 2928-SFP Plus BOOTROM, Version 119                 *
    *                                                                      *
    ************************************************************************
    Creation Date       : Feb  3 2010
    CPU L1 Cache        : 32KB
    CPU Clock Speed     : 333MHz
    Memory Size         : 128MB
    Flash Size          : 128MB
    CPLD Version        : 002
    PCB Version         : Ver.B
    Mac Address         : 002473959EC8


Press Ctrl-B to enter Extended Boot menu...0
Starting to get the main application file--flash:/S2900-CMW520-R1101P09.bin!...
..........................................................................
The main application file is self-decompressing................................
...............................................................................
.........................Done!
System is starting...
Startup configuration file does not exist.
User interface aux0 is available.
</code>

13. Press "Enter", then enter the username "admin" and password "<blank>". Press "Enter" and you will be logged in.
<code>
 Press ENTER to get started.

Login authentication


Username:admin
Password:
<3Com Baseline Switch>
#Apr 26 12:00:19:811 2000 this article is from VMadmin.co.uk 3Com Baseline Switch SHELL/4/LOGIN:
 Trap 1.3.6.1.4.1.43.45.1.10.2.2.1.1.3.0.1<h3cLogIn>:admin login from Console
%Apr 26 12:00:19:981 2000 3Com Baseline Switch SHELL/4/LOGIN: admin login from aux0
<3Com Baseline Switch>
<3Com Baseline Switch>
</code>

14.  If you type "summary" you will see all the switch details.

Amongst these details are the IP address of the switch. If you have DHCP on your network this switch is connected to it will receive one as in my case below, so I can now configure the rest via a web browser.

If not you can use the "ipsetup" command to set a static management IP and access via a web browser.
<code>
<3Com Baseline Switch>summary
Select menu option:             Summary
IP Method:                      DHCP
IP address:                     192.168.1.250
Subnet mask:                    255.255.255.0
Default gateway:                192.168.1.254

Current boot app is: flash:/S2900-CMW520-R1101P09.bin
Next main boot app is: flash:/s2900-cmw520-r1101p09.bin
Next backup boot app is: NULL

3Com Corporation
3Com Baseline Switch 2928-SFP Plus Software Version 5.20 Release 1101P09
Copyright (c) 2004-2010 3Com Corp. and its licensors. All rights reserved.
3Com Baseline Switch 2928-SFP Plus uptime is 0 week, 0 day, 0 hour, 1 minute

3Com Baseline Switch 2928-SFP Plus
128M    bytes DRAM
128M    bytes Nand Flash Memory
Config Register points to Nand Flash

Hardware Version is REV.B
CPLD Version is 002
Bootrom Version is 119
[SubSlot 0] 24GE+4SFP Hardware Version is REV.B

<3Com Baseline Switch>
</code>
 
15. Once you can access the web management page for the switch make sure you set a strong password for "admin" and store it in a secure encrypted location for next time.

16. Don't forget to save your new configuration! Otherwise the switch will be at factory defaults if the power goes off!!